A chill instrument is one that has an instrumentation of 80s style and is played by someone who knows the basics of music.
Here are the steps to making your own chill instrument.1.
Get the materials you want to make your own instrument.
The materials you’ll need to make a chill instrument are: a piece of wood or plywood with an attached neck (you can also buy a piece that is made from a piece you already have laying around), a string or string instrument that will hold the strings (if you have a string instrument, you can use that to play the strings), a drum stand that will sit on the back of your guitar or bass, a set of earbuds (they come in different sizes and can be used with different instruments), and a guitar pick.2.
Measure the neck.
Measure your neck to determine its thickness.
For example, if the neck is about 1 1/2 inches (25 centimeters) in diameter, then you can make a small instrument out of it.
If the neck measures 1 inch (25.6 centimeters) across, you’ll have to make it into a guitar or a bass.3.
Find a piece.
This is a piece the listener can hold while they play and it will have a fixed neck so the strings can rest on it.
You can also get a piece from a guitar that is just sitting there, or make it a part of your own guitar.4.
Find the right neck.
Find an instrument that you can hold on to while you play, like a bass, guitar, or mandolin.
Make sure the neck isn’t too big and you’re able to bend it enough to allow you to play with it.5.
Cut the neck pieces.
Cut each piece of the neck to length, and you can also trim the sides to make them easier to use later.
Cut them at a 45 degree angle so that they will lay flat when you play them.
You should have about four pieces of each piece.6.
Measure and cut the neck strings.
Measure one string and cut it down so that it’s about 1/8 inch (4.6 millimeters) long.
Cut it into two sections and put them together to make one string.
If you’re using a string that is about a half-inch (3.8 millimeters).
shorter than the length of the string, cut the string into two halves and measure them together.
Make the string so it is about the length you want.
If it’s a little longer than that, you’re probably going to have to shorten it or lengthen it to make sure it will fit.
The length of this string should be about one and a half inches (38 centimeters).7.
Cut out the neck piece.
Cut this piece to length.
Make a small indentation about 1 inch (.5 centimeters) wide on the top of the piece of string.
Cut a piece out of the other piece and measure the length and thickness of the length piece.
You’ll need one of these measurements, one for each string.8.
Cut and glue the pieces together.
To make the glue, place the pieces of string on a dry towel and spread glue on them.
Gently press the pieces back together until the glue is completely dried.9.
Stick the strings together.
Slide the string pieces into place.
Use a string-stretcher or a pencil to press the strings into place so that the glue doesn’t rub off.
The glue will be sticky and the strings will probably stick together.10.
Put the pieces into the case.
Now it’s time to put the instruments back into the guitar or the bass.
You want the neck-pieces to be in the back.
Make two small indentations on the bottom of the case and glue these two pieces together with glue.
This will give the instrument a flat, rounded look.11.
Put it back together.
Now you’re ready to play it.
Put a piece on the guitar and string the string through the holes in the case with the guitar pick, so that there is a little space between the neck and the pick.
This makes it easier to bend the strings.
You may have to use a small hammer or a nail to make the pick stick.12.
Try it out.
Let your friend or someone else play the guitar with you while you record or play the song with the instruments.
Let them play the piece, then let them record it.
And let them play it again and record the same thing over and over again.
You don’t have to let them repeat the same song.